Stiebel Eltron Mini™ 2-1 120 Volt (110 V)
Point-of-Use Tankless Water Heater

call our water heating experts!
Let us help you evaluate if tankless is right for you or help you select the best model for your application. Call us now...

Stiebel Eltron
Mini 2 Advantages:

• save space

• save energy

• reduce water waste

• simple installation

• very economical

• legendary Stiebel quality

Download Stiebel Eltron Mini 2 Tankless Brochure

Stiebel Eltron Mini 2 Tankless Brochure

Adobe PDF Format

Download Stiebel Eltron Mini 2 Tankless Water Heater Installation Manual

Stiebel Eltron Mini 2 Tankless Installation Guide

Adobe PDF Format

ELT Listed - USA & Canada

the Stiebel Eltron Mini Series
tankless water heaters are independently tested to comply with US and Canadian safety standards

WQA Certified

Stiebel Eltron Tankless Water Heaters are tested and certified by WQA against NSF/ANSI 372 for "lead free" compliance.

Stiebel Eltron is
Stiebel Eltron is ISO-9001 Certified
Quality you can count on!
Manufactured in Germany

Stiebel Eltron Mini 2-1

Our Price: US$159.00

(In Stock)

Found a Lower Price?
Request a Price Beat

  • 1.8 kW's of Power
  • Flow Control Activated
  • Ultra Compact Size
  • 110v

The Stiebel Eltron Mini™ Series tankless water heaters are economical, ultra-compact, attractive point-of-use tankless water heaters designed for consistent, low-flow, point-of-use applications. The Mini Series is most suited to applications which possess a relatively constant flow rate. If the flow rate of your application is likely to fluctuate due to varying water demands or varying water pressures, etc., we recommend that you consider a DHC-E 8/10 tankless water heater instead as they include thermostatic control and flow-based power modulation technology.

Due to its compact size, the Stiebel Eltron Mini 2 easily fits directly under a sink or an adjacent cupboard or closet, so it delivers hot water straight to the sink with almost no delay. By locating the heater right next to where the hot water will be used, you can also virtually eliminate thermal heat loss which is commonly associated with long pipe runs. If the Mini 2 is able to supply all of the hot water needs for the entire room, you can also eliminate the need to run a hot water line all the way from the main central water heater in new construction applications.

The Mini 2-1 is extremely energy efficient as it produces hot water on demand only as it is required. A sophisticated water flow sensor recognizes when hot water is being used and activates and deactivates the unit automatically so it only runs when you are actually using water. This eliminates standby thermal heat losses often associated with traditional tank style water heaters. Due to this, you can expect to see a significant cost reduction over the operating cost of a conventional water heater.

Maximum Flow Rate in Gallons Per Minute at 105F Output Temp.
Incoming Water Temp: Flow Rate (GPM)
Not recommended below 55F
55F 0.25 GPM
60F 0.32 GPM
65F 0.32 GPM
70F 0.32 GPM
75F 0.32 GPM
80F 0.32 GPM
* This chart is based on 120v power input.

Do You Have Hard Water?
If your water hardness exceeds 7 grains per gallon (GPG) or 120 mg/l (ppm), you should consider hard water treatment prior to your tankless water heater. If your hardness exceeds 12 GPG or 200 mg/l (ppm), hard water treatment is strongly recommended.

Hard water treatment helps maintain performance and efficiency, ensures optimal water flow and pressure, and protects your heater from pre-mature failure due to mineral build-up inside the heating module and other components.

Tankless & Hard Water

All Mini Series tankless water heaters are equipped with a safety high-limit with manual reset. Mini 2-1 units are internally restricted to 0.32 GPM / 1.2 l/min.

The Stiebel Eltron Mini 2 is not recommended for whole house use. For more information on whole house models, see our Stiebel Eltron Tempra Series Whole House Tankless Water Heaters.

Stiebel Eltron Mini 2 Tankless Water Heater Specifications
KW 1.8 KW @ 120V
Voltage: 110 to 120 volts / single phase / 50 - 60 Hz
Max. Amps: 15 AMPS
Breakers Required:*  1 x 15 AMP breaker
Wiring:*  Minimum #14 AWG Copper
Minimum Water Resistivity 2795 ohm x in / 1100 ohm x cm
Degree of protection according to IEC 529 IP 24
Dimensions (H x D X W): 6.5 x 3.25 x 7.5" (16.5 x 8.2 x 19 cm)
Weight: 3.4 lbs (1.6 KG)
Pipe Fittings:  for 3/8" O.D. flex connector
Energy Efficiency: 99%+
Activation Flow Rate: 0.21 GPM / 0.8 LPM
Max. Water Pressure:    150 psi
Warranty: Manufacturer's 3 Year Warranty
Safety: ETL Listed (US / Canada)
Protection: thermal hi-limit cut-out switch

* Breaker size and wire gauge must meet all applicable local, state, provincial, and national electrical codes for your area - these are only guidelines that will apply to most installations. Please consult your electrician for more details.