USD / CAD
CART
1-877-374-2696

Stiebel Eltron DHC-E 8/10 Point-of-Use
Tankless Water Heater

Stiebel Eltron DHC-E 8/10

MSRP: US$319.00
Our Price: US$249.00
You save: $70.00



- or -
Make us an offer for the Stiebel Eltron DHC-E 8/10
5.0 out of 5 stars
5.0 out of 5 stars (3 reviews)
Review this product

Found a Lower Price?
Request a Price Beat
Free Shipping
Lowest Price Guaranteed on the Stiebel Eltron DHC-E 8/10

Lowest Price Guaranteed!

If you find a lower price on this product call us or Click here to request a price beat.

Stiebel Eltron DHC-E 8/10

  • Description
  • Specifications
  • Installation / Manual
  • FAQ
  • Reviews
  • Validations
  • Hard Water
Maximum Flow Rate in Gallons Per Minute at 105F Output Temp.
Incoming Water Temp: Flow Rate (GPM)
40F 0.75 / 1.00 GPM
45F 0.82 / 1.09 GPM
50F 0.89 / 1.19 GPM
55F 0.98 / 1.31 GPM
60F 1.09 / 1.45 GPM
65F 1.22 / 1.63 GPM
70F 1.40 / 1.87 GPM
75F 1.63 / 2.18 GPM

The Stiebel Eltron DHC-E series tankless water heaters are the most advanced point-of-use tankless water heaters on the market today. The DHC-E 8/10 and DHC-E 12 both feature the same industry-leading thermostatic temperature control and flow and temperature based power modulation technology found in Stiebel Eltron's flagship Tempra whole house heaters. Set the desired temperature on the front of the unit and enjoy water temperatures between 86° (30°C), and 140° (60°C). Change the desired temperature at anytime. Advanced microprocessor technology ensures that the water temperature never deviates from the set point.

By producing hot water on demand only as it is being used, the DHC-E 8/10 is extremely energy efficient. A sophisticated water flow sensor recognizes when hot water is being used and when it has been turned off, so the unit will activate and deactivate automatically so it only runs when you are actually using water. This eliminates standby thermal heat losses associated with traditional tank type water heaters. Accordingly, you can expect to see a significant cost reduction over the operating cost of a conventional water heater.

The Stiebel Eltron DHC-E 8/10 combines the DHC-E 8 and DHC-E 10 into a single unit. Changing a jumper during installation allows this unit to act as either an 8 KW or 10 KW unit.

The Stiebel Eltron DHC-E series tankless water heaters are the most technologically advanced point-of-use tankless water heaters available today. The DHC-E 8, DHC-E 8/10 and DHC-E 12 feature the industry-leading thermostatic temperature control as well as flow and temperature based power modulation technology found in Stiebel Eltron's flagship Tempra whole house heaters. Simply set your desired temperature between 86° (30°C), and 140° (60°C) and enjoy water at the temperature you requested. Change your desired temperature at anytime with ease. Advanced microprocessor technology ensures that the water temperature never deviates from your desired temperature.

The DHC-E 8/10 is extremely energy efficient, as it produces hot water on demand only as it is required. A sophisticated water flow sensor recognizes when hot water is turned on and when it has been turned off, so the unit will activate and deactivate automatically. This ensures it will only run when you are actually requesting hot water. You can expect to see a significant cost reduction over the operating cost of a conventional water heater, as this eliminates standby thermal heat losses associated with traditional tank type water heaters.

  • 7.2 or 9.6 kW's of Power
  • Thermostatically Controlled
  • Compact Size
  • 240v

Stiebel Eltron DHC-E 8/10 Classic Specifications

Heating System? Direct Coil™
KW 9.6 KW @ 240v / 7.2 KW @ 208v
Voltage: 208 - 240 volts / single phase / 50 - 60 Hz
Max. Amps: 40 AMPS @ 240v / 35 AMPS @ 208v
Breakers Required:*  1 x 40 AMP breaker @ 240V
or 1 x 35 amp breaker at 208V (depends on local codes)
Wiring:*  Minimum #8 AWG Copper (depends on local codes)
Dimensions: 14.25 x 7.9 x 4.1" (36 x 20 x 11 cm)
Weight: 5.9 lbs (2.7 KG)
Pipe Fittings:  1/2" NPT
Energy Efficiency: 99%+
Activation Flow Rate: 0.26 GPM / 1.0 LPM
Max. Water Pressure:    150 psi
Warranty: Manufacturer's 3 Year Warranty
Safety: ETL Listed (US / Canada)
Protection: microprocessor-based thermostatic temperature control (flow rate and temperature modulating) with thermal hi-limit cut-out switch

* Breaker size and wire gauge must meet all applicable local, state, provincial, and national electrical codes for your area - these are only guidelines that will apply to most installations. Please consult your electrician for more details.

Stiebel Eltron DHC-E 8/10 Customer Questions & Answers


No customer questions have been submitted for this. Have a question? Ask it above.

Other DHC-E Series Reviews

on-demand hot water5 Stars
Product is working fine. The only thing I miss is that this new model doesn't have an indicator light to show that power is on until you start the water flow thru it. Other than than, it works great - Bruce

It’s ok5 Stars
Honest review. It works. But you have to turn water pressure down in shower before it gets warm. Thinking about buying another and run water through both to get it hot. - Mkeith

I'm singing in the shower!5 Stars
Temperature setting is only half way up and is delivering endless hot water making for a very enjoyable shower. - LD White





Stiebel Eltron is:
Stiebel Eltron is ISO-9001 Certified
ETL Listed - USA & Canada!
All Stiebel Eltron Tempra Trend tankless water heaters are ETL Listed in the USA and Canada, ensuring they conform to all applicable safety standards.
WQA Certified - USA & Canada!
All Stiebel Eltron Tankless Water Heaters are tested and certified by WQA against NSF/ANSI 372 for "lead free" compliance.


Do You Have Hard Water?

ecoTAC discount offer
If your water hardness trends above 7 grains per gallon (GPG) or 120 mg/l (ppm), you should consider hard water treatment prior to your tankless water heater. If your hardness exceeds 12 GPG or 200 mg/l (ppm), hard water treatment is strongly recommended.

Hard water treatment helps maintain performance and efficiency, ensures optimal water flow and pressure, and protects your heater from pre-mature failure due to mineral build-up inside the heating module and other components.